Our Flush Frame roof skylights can be manufactured in a variety of shapes and sizes including square, rectangular and triangular. The system offers a very low profile as the glass is structurally bonded and triple sealed making it ideal for flat roof applications on a pitch of only 3-5 degrees.

Specifications

Standard Maximum Kerb Width: 1500mm x 3500mm
Standard Minimum Kerb Width: 400mm x 400mm
Kerb Width Minimum: 75mm
Kerb Height Minimum: 150mm
Minimum Kerb pitch: 3-5º

Standard Sizes and Prices

In addition to bespoke sizes we also offer a number of stock roof skylights which can be delivered in 2 - 3 weeks from order. Our stock Flush Frame systems EXCLUDE delivery. An optional installation service is available at additional cost.

£938.00 (excluding VAT)

£1,025.00 (excluding VAT)

£999.00 (excluding VAT)

£1,153.00 (excluding VAT)

£1,308.00 (excluding VAT)

£1,129.00 (excluding VAT)

£1,233.00 (excluding VAT)

Modular

Our Flush Frame modular system has been developed to cater for joining individual roof skylights together to create large expanses of glazing.

Glass can be divided into sections and joined together using a silicone seal for anything less than a span of 1350mm, anything greater than 1350mm then either an aluminum back to back angle or glass fin (not an option with walk on) will be required

Standard Glass Specification

26mm Double Glazed Unit – 4mm Toughened Outer Pane, 16mm Argon filled cavity, 6mm Low E Soft Coat Toughened Inner Pane

Various glass specifications can be provided for dependent on the client’s requirement, whether the need for improved solar performance or increased security we will produce a configuration to suit.

Laminated glass inner panes should be used when the roof light will be installed over a fall of over 5metres or the roof light is to be position above a swimming pool this will reduce the square meter rate achievable as one pane to 3.25m²

Colour

Our Roof Skylights are powder coated to a dual colour finish, RAL 9010 White internally and RAL7015 Slate Grey to the outside, alternative paint specifications are available as an extra

Warranty

Our Flush Frame Sky lights comes with a standard 5 year warranty

Installation

Installation onto prepared roof apertures and up-stands is simple, each of the roof skylights is supplied assembled, packaged with instructions and fitting kit. For supply only contracts we supply full installation instructions, or opt for our installation service.

An on site lifting facility will be required to locate the heavier units to the roof location.

Please remember to specify the Internal Kerb dimensions of the opening.

Our Flush Frame Walk-On sky light offers the same characteristics as our standard fixed sky lights however it can be tailored so that it finishes flush with internal or external flooring to provide a seamless finish.

The Walk-On skylights has been designed specifically for areas requiring pedestrian access, it can be tailored to meet many shapes and sizes from square, rectangular, circular, triangular and many other bespoke configurations.

Specifications

Maximum Kerb Width: 1200mm x 2500mm
Minimum Kerb Width: 400mm x 400mm
Kerb Width Minimum: 75mm
Kerb Height Minimum: 150mm
Minimum Kerb pitch: 1º

Standard Sizes and Prices

In addition to bespoke sizes we also offer a number of stock flush roof Flush Frame flat roof lights which can be delivered in 2 - 3 weeks from order. Our stock systems EXCLUDE delivery. An optional installation service is available at additional cost.

1,498.00 (excluding VAT)

£1,760.00 (excluding VAT)

£1,681.00 (excluding VAT)

£2,157.00 (excluding VAT)

£2,633.00 (excluding VAT)

£2,093.00 (excluding VAT)

£2,427.00 (excluding VAT)

Standard Glass Specification

47.5mm Double Glazed Unit – 25.5mm Toughened Outer Pane, 16mm Argon filled cavity, 6mm Toughened Inner Pane

Various glass specifications can be provided for dependent on the client’s requirement, whether the need for improved solar performance or increased security we will produce a configuration to suit.

Colour

All our roof skylights are powder coated to a dual colour finish, RAL 9010 White internally and RAL 9005 Black to the outside, alternative paint specifications are available as an extra

Warranty

Our Flush Frame Roof Skylights comes with a standard 5 year warranty

Installation

Installation onto prepared roof apertures and up-stands is simple, each roof light is supplied assembled, packaged with instructions and fitting kit. For supply only contracts we supply full installation instructions, or opt for our installation service.

An on site lifting facility will be required to locate the heavier units to the roof location.

Please remember to specify the Internal Kerb dimensions of the opening.

Our Flush Frame system can also be incorporated into hipped, double hipped and pyramid shaded skylights. Utilising excellent thermal qualities with a contemporary architectural design this system uses 40% less frame than our standard aluminium thermally broken aluminium roof lights.

Specifications

Maximum Square Kerb Width: 1500mm x 1500mm
Minimum Square Kerb Width: 600mm x 600mm
Maximum Elongated Kerb Width: 1500mm x 2500mm
Minimum Elongated Kerb Width: 600mm x 600mm
Kerb Width Minimum: 75mm
Kerb Height Minimum: 150mm

Standard Sizes and Prices

In addition to bespoke sizes we also offer a number of stock sky lights which can be delivered in 2 - 3 weeks from order. Our stock Flush Frame systems EXCLUDE delivery. An optional installation service is available at additional cost.

£1,608.00 (excluding VAT)

£1,738.00 (excluding VAT)

£1,745.00 (excluding VAT)

£1,961.00 (excluding VAT)

£2,185.00 (excluding VAT)

£2,019.00 (excluding VAT)

£2,164.00 (excluding VAT)

Standard Glass Specification

26mm Double Glazed Unit – 4mm Toughened Outer Pane, 16mm Argon filled cavity, 6mm Low E Soft Coat Toughened Inner Pane

Colour

All our roof skylights are powder coated to a dual colour finish, RAL 9010 White internally and RAL7015 Slate Grey to the outside, alternative paint specifications are available as an extra

Warranty

Our Flush glaze Roof skylight comes with a standard 5 year warranty

Installation

Installation onto prepared roof apertures and up-stands is simple, each flat roof light is supplied assembled, packaged with instructions and fitting kit. For supply only contracts we supply full installation instructions, or opt for our installation service.

An on site lifting facility will be required to locate the heavier units to the roof location.

Please remember to specify the Internal Kerb dimensions of the opening.

Our Hinged Flush Frame system is impeccably designed combining leading thermal performance with the highest quality, fully concealed opening mechanism, maintaining contemporary design.

This system is chain driven and opens the Flush Frame roof skylights to a maximum of 400mm

Features

Concealed operating mechanism
Flushglazed - no water ponding
Maximum daylight - minimum framework
Low-E double skinned safety glass
High security
Simple installation
Safe low voltage operation
Extensive size range

Standard Sizes and Prices

In addition to bespoke sizes we also offer a number of stock flat sky lights which can be delivered in 2 - 3 weeks from order. Our stock Flush Frame systems EXCLUDE delivery. An optional installation service is available at additional cost.

£1,687.00 (excluding VAT)

£2,064.00 (excluding VAT)

£1,742.00 (excluding VAT)

£2,178.00 (excluding VAT)

£2,615.00 (excluding VAT)

£2,155.00 (excluding VAT)

£2,543.00 (excluding VAT)

Specifications

Max Width: 2400mm
Max Area (subject to snow loads): 3 sq m
Minimum length: 750mm
Minimum width (hinged side): 450mm

Options

Remote control
Rain sensors
Temperature sensors
Battery Back up

Standard Glass Specification

26mm Double Glazed Unit – 6mm Toughened Outer Pane, 16mm Argon filled cavity, 6mm Toughened Inner Pane

Various glass specifications can be provided for dependent on the client’s requirement, whether the need for improved solar performance or increased security we will produce a configuration to suit.

Laminated glass inner panes should be used when the roof light will be installed over a fall of over 5metres or the roof light is to be position above a swimming pool this will reduce the square meter rate achievable as one pane to 3.25m²

Colour

All our roof skylights are powder coated to a dual colour finish, RAL 9010 White internally and RAL7015 Slate Grey to the outside, alternative paint specifications are available as an extra

Warranty

Our Flush Frame sky light comes with a standard 5 year warranty

Installation

Installation onto prepared roof apertures and up-stands is simple, each roof skylight is supplied assembled, packaged with instructions and fitting kit. For supply only contracts we supply full installation instructions, or opt for our installation service.

An on site lifting facility will be required to locate the heavier units to the roof location.

Please remember to specify the Internal Kerb dimensions of the opening.

Our Access Flush Frame roof skylight is a simple thermally broken manual hinged skylight. Gas struts make operation simple and efficient and assist in keeping the rooflight stable once open.

Features

Simple single latch operation
Fully openable to approximately 85 degrees
Gas struts make stable once in open position
Flush glazing or insulated panel 

Standard Sizes and Prices

In addition to bespoke sizes we also offer a number of stock sky lights which can be delivered in 2 - 3 weeks from order. Our stock Flush Frame systems prices EXCLUDE delivery. An optional installation service is available at an additional cost

£1,102.00 (excluding VAT)

£1,486 (excluding VAT)

£1,595.00 (excluding VAT)

£1,667.00 (excluding VAT)

Standard Glass Specification

26mm Double Glazed Unit – 4mm Toughened Outer Pane, 16mm Argon filled cavity, 6mm Low E Soft Coat Toughened Inner Pane

Various glass specifications can be provided for dependent on the client’s requirement, whether the need for improved solar performance or increased security we will produce a configuration to suit.

Colour

Our Sky lights are powder coated to a dual colour finish, RAL 9010 White internally and RAL7015 Slate Grey to the outside, alternative paint specifications are available as an extra

Warranty

Our Flush Frame sky light comes with a standard 5 year warranty

Installation

Installation onto prepared roof apertures and up-stands is simple, each roof skylight is supplied assembled, packaged with instructions and fitting kit. For supply only contracts we supply full installation instructions, or opt for our installation service.

An on site lifting facility will be required to locate the heavier units to the roof location.

Please remember to specify the Internal Kerb dimensions of the opening.

This system uterlises the flush glaze principles it offers unique characteristics of frameless glazing to achieve maximum daylight, longevity and high performance. We use a telescopic cantilevering mechanism to create an almost 100% clear opening.

The roof skylight is opened electrically, operated by a rocker switch positioned at the discretion of the client.

Skyglide Rooflight Technical Data

Required Kerb height: 150mm (to avoid invalidating roof guarantees)
Minimum Kerb thickness: 166mm stepped kerb required (drawings provided)
Maximum Length: (travelling) 1500mm
Minimum Length (travelling): 600mm
Speed of operation: 2-3m/min (variable)
Maximum overall version for Flushglaze version 3m2
Maximun overall area for Skyline version 2.25m2

Standard Glass Specification

28mm Double Glazed Unit – 6mm Toughened Outer Pane, 16mm Argon filled cavity, 6mm Toughened Inner Pane

Colour

All our roof lights are Powder coated to either RAL7015 Grey or RAL9010 White, alternative paint specifications are available however these can effect both price and lead times.

Warranty

Our Flush glaze roof skylight comes with a standard 5 year warranty

Installation

Installation onto prepared roof apertures and up-stands is simple, each flat  sky light is supplied assembled, packaged with instructions and fitting kit. For supply only contracts we supply full installation instructions, or opt for our installation service.

An on site lifting facility will be required to locate the heavier units to the roof location.

Please remember when requesting a quote, specify the outside dimensions of the opening / kerb, you should then make an allowance of approximately 150mm for inside dimensions subject to chosen internal finishes dimension.

Designed as a more cost effective alternative to our bespoke sliding roof skylight range. This flat sky light comes in 2 sections, one sliding section sliding over one fixed section, creating a 50% clear opening. All the glass used is flush to allow water run off and easy cleaning.

Sliding Over Fixed Roof Light

Clear opening: 50%
Maximum Span: 2400mm
Minimum Length (travelling): 1500mm
Maximum footprint area: 10m2
Speed of operation: 2-3m/min (variable)

Standard Glass Specification

28mm Double Glazed Unit – 6mm Toughened Outer Pane, 16mm Argon filled cavity, 6mm Toughened Inner Pane

Colour

All our roof lights are Powder coated to either RAL7015 Grey or RAL9010 White, alternative paint specifications are available however these can effect both price and lead times.

Warranty

Our Flush glaze Rooflight comes with a standard 5 year warranty

Installation

Installation onto prepared roof apertures and up-stands is simple, each flat roof light is supplied assembled, packaged with instructions and fitting kit. For supply only contracts we supply full installation instructions, or opt for our installation service.

An on site lifting facility will be required to locate the heavier units to the roof location.

Please remember when requesting a quote, specify the outside dimensions of the opening / kerb, you should then make an allowance of approximately 150mm for inside dimensions subject to chosen internal finishes dimension.